Fire Rated Walls

Guide · Homeowners · 3 min read · Updated 17 November 2026

How Much Does a Fire Rated Wall Cost in the UK?

Short answer

A new fire rated stud partition in the UK typically costs £55–£85 per m² for 30 minutes and £75–£120 per m² for 60 minutes. Upgrading an existing wall to 30 minutes costs £35–£65 per m². Loft conversion stair protection costs £900–£2,500, boxing a steel beam £250–£600 per beam and fire stopping penetrations from £25 each. Prices depend on the tested system, access and finish.

How Much Does a Fire Rated Wall Cost in the UK?

Typical fire rated wall prices in 2026

Fire rated walls are usually priced per square metre for partitions and upgrades, and per item for fire stopping, steel protection and loft stairs. The figures below assume standard ceiling heights, clear access and a manufacturer's tested system of plasterboard, studs and insulation, finished ready for skim or decoration. Small jobs have a minimum charge, because setting up and making good takes similar time whether the wall is three or ten square metres.

JobTypical priceNotes
30 minute stud partition£55–£85 per m²Single or double layer fire board each side
60 minute stud partition£75–£120 per m²Usually two layers each side plus insulation
Upgrade existing wall to 30 minutes£35–£65 per m²Extra fire board over sound existing wall
Loft conversion stair protection£900–£2,500Enclosure and linings to the protected route
Steel beam boxing£250–£600 per beamFire board encasement to the required period
Fire stopping penetrationsfrom £25 per penetrationSealing pipes and cables through rated walls

Why 60 minutes costs more than 30

A wall's fire resistance comes from the whole tested system, not from one material. A typical 30 minute stud partition uses a single layer of fire-resistant plasterboard on each side of a metal or timber stud frame. A 60 minute partition usually needs two layers each side, often with mineral wool insulation in the cavity, and closer attention to fixings and joints. That doubles the boarding and adds labour, which is why 60 minute walls cost noticeably more per square metre.

Some walls need a higher rating still, such as 90 or 120 minutes between compartments in larger commercial or residential buildings. These use heavier systems with more layers and are priced on specification.

What else affects the price

Beyond the fire rating, the details around the wall drive the cost. Every door in a fire rated wall needs a fire door set of matching performance. Every pipe, cable and duct that passes through needs fire stopping. Where the wall meets the ceiling, the fire resistance must continue to the structural soffit, not stop at a suspended ceiling, which can mean working in tight voids.

  • Fire rating required: 30, 60 or more minutes
  • Wall height: walls running into a roof void or above a suspended ceiling cost more
  • Number of service penetrations to fire stop
  • Doors and glazing within the wall, which need matching fire rated sets
  • Acoustic requirements combined with fire resistance
  • Access: occupied buildings, out of hours work or high level access
  • Finish: taped and filled, skimmed or ready to decorate

Loft conversions and steel protection

Loft conversion stair protection costs £900–£2,500. Approved Document B requires a protected escape route when a new storey is added to a typical house in England, so the stair enclosure and the walls to the escape route must be fire resisting. Depending on the house, work can include new fire rated partitions around the stair, upgrading existing walls, fitting fire doors to habitable rooms off the route and fire stopping around services.

Steel beam boxing costs £250–£600 per beam. Steel loses strength in a fire, so beams supporting floors or walls above are often encased in fire-resistant board to give the required period of protection. The board is fixed to a framework around the beam using the manufacturer's system, with joints taped and filled.

Fire stopping and upgrades

Fire stopping penetrations from £25 each is one of the most important and most overlooked costs. A fire rated wall is only as good as its weakest gap. Pipes, cables and ducts that pass through must be sealed with tested products such as intumescent sealant, fire collars on plastic pipes or fire batts, installed as the product's approval specifies.

Upgrading an existing wall at £35–£65 per m² is a cost-effective option where the existing wall is sound. Additional fire-resistant board is fixed over it to a tested specification. It is common in loft conversions, HMO upgrades and garage separation, where rebuilding the wall would be disruptive.

Getting an accurate quote

Tell the installer what rating is needed and why, for example a building control requirement, a fire risk assessment recommendation or an insurer's request. Share drawings or a building control plan if you have them. Send photos of the area, including ceilings, services passing through and any doors. Ask for the quote to name the tested system, the fire rating and what is included at the head of the wall. That makes it easy to compare quotes and to show building control what has been installed.

Paperwork worth asking for

Fire rated construction is hidden once it is boarded and decorated, so evidence of what was built matters. Ask for the system name and the manufacturer's data sheet, photos taken during installation showing board layers and fire stopping, and a schedule of penetrations sealed with the products used. Building control officers, fire risk assessors and insurers may ask to see this, and having it saves opening walls up later to check.

For commercial premises and HMOs, keep these records with the fire risk assessment, because the responsible person will need to show that fire safety measures are maintained. When future trades cut new holes for cables or pipes, the same records show what fire stopping should be reinstated.

Questions people also ask

How much does a 30 minute fire rated wall cost?

A new 30 minute fire rated stud partition typically costs £55–£85 per m². It usually uses one layer of fire-resistant plasterboard on each side of a stud frame, built to a manufacturer's tested system. Doors, fire stopping and finishing are often priced separately, so check what each quote includes.

Is it cheaper to upgrade an existing wall than build a new one?

Usually, yes. Upgrading a sound existing wall to 30 minutes costs £35–£65 per m², compared with £55–£85 per m² for a new partition. Extra fire board is fixed over the wall to a tested specification. The existing wall must be in good condition and the upgrade must continue to the structural ceiling.

Do fire rated walls need building control approval?

Most do when they form part of building work, such as a loft conversion, extension, change of use or new partition affecting escape routes. Building control will check the fire resistance meets Approved Document B in England. Work on higher-risk buildings needs approval from the Building Safety Regulator.

Written and checked by the Fire Rated Walls team. Read our editorial policy.

Get a free fire rated walls quote

Tell us what you need and we'll come back with a clear price.

Request a quote